GMRS Guide
A bearded trucker smiling from the driver's seat of his cab at night, lights blurred through the window behind him

How to adjust a CB radio: every knob, in the order that works

Most CBs that 'don't work' have a squelch set too high, RF gain turned down or an untuned antenna. Set them in this order and you'll hear what's actually out there.

How we pick · Updated · We earn a commission when you buy through our Amazon links.

To adjust a CB radio, check the antenna's SWR first, then set volume, squelch just past the hiss, RF gain fully up, ANL on, mic gain up, and delta tune centered. Do them in that order, because each step changes what you hear for the next. A CB with squelch cranked up and RF gain turned down can sit silent next to a busy channel 19.

Where these settings come from

The settings below come from Cobra's two support articles on CB controls ("CB control settings" and "CB radio operation: front panel controls"), the control lists on current Uniden and President listings, and the FCC rules in 47 CFR Part 95, read in the eCFR on October 21, 2026. The trouble-shooting table draws on the questions truckers post in forum threads about the Cobra 29.

"How we pick" is our label for research from manufacturer documentation and the rules. These are published settings, not results of a bench test we ran. How we research.

Step 1: check the SWR before you touch the knobs

Adjusting the radio can't fix a bad antenna match. If SWR is high, the radio sounds weak no matter where the knobs sit, and the club8090 tuning wiki warns that anything above 3 to 1 is harmful to the radio. So check it first, on a radio with a built-in meter, using Cobra's published steps:

  1. Park in the open, away from buildings, with the doors shut.
  2. Select channel 1. Set the meter switch to CAL.
  3. Key the mic and turn the SWR CAL knob until the needle reaches the calibration mark (a triangle on Cobra meters).
  4. Still keying, switch to SWR and read the scale. Let go.
  5. Repeat on channel 40.

Cobra's line is that SWR must be below 3. Our guide to tuning a CB antenna aims lower, under 1.5 to 1 on both channels, and shows how to lengthen or shorten the antenna when channel 1 and channel 40 disagree. No built-in meter? An inline 27 MHz meter like the SURECOM SW-111 (it covers 26.965 to 27.405 MHz) or the Workman SWR2T with a 3-foot jumper does the same job. When you're done, put the meter switch back to S/RF for normal use.

Step 2: set the knobs in this order

  1. Volume. Turn squelch fully counterclockwise so you hear hiss, then set volume to a comfortable level over road noise.
  2. Squelch. Slowly turn it up until the hiss just stops. Not one bit more.
  3. RF gain. Fully clockwise. If you turned it down earlier, re-check the squelch afterward, because the two interact.
  4. ANL on. NB off unless you hear repetitive popping.
  5. Mic gain (Cobra calls it Dynamike). Fully up with the stock mic.
  6. Delta tune or clarifier at center.
  7. Switches. CH9/19 to NORMAL, PA/CB to CB, and power to high if your radio has a high/low switch.

Do this on the highway or at a truck stop, not in a quiet garage. Squelch set at home in silence will be wrong once the engine is running.

What each control does

ControlWhat it doesStart hereWrong sounds like
SquelchMutes the speaker until a signal is strong enoughJust past where the hiss stopsToo high: dead silence while others talk. Too low: constant hiss
RF gainReceiver sensitivityFully upToo low: only close trucks come through
ANLClips engine and ignition noise spikesOn in a vehicleOff: popping and whine under voices
NB (noise blanker)Stronger filter for repetitive pulse noiseOff unless neededOn when not needed: slightly weaker reception
Mic gain / DynamikeHow hard your voice drives the transmitterFully up with a stock micToo high with a power mic: squeal or distortion
Delta tune / clarifierFine-tunes reception only12 o'clockOff-center: voices sound tinny or warbled
Hi-CutRolls off high-pitched hissTry on and offOn: slightly muffled audio
SWR CALSets the built-in meter for an SWR readingOnly during SWR checksLeft in CAL/SWR: no normal meter reading

Recommended settings for squelch, RF gain, Dynamike, Delta Tune, ANL and NB from Cobra's "CB control settings" and "front panel controls" support articles.

Squelch and RF gain work together

Squelch opens when a signal is stronger than its threshold. RF gain sets how strong signals look to the receiver. So turning RF gain down has the same effect as turning squelch up: weaker stations stop breaking through. That's why you set squelch with RF gain fully up, and why a radio with both knobs halfway seems to have no range at all.

There's a good use for the combination. On a crowded channel 19 near a city, turn RF gain down until only the trucks around you come through, then nudge squelch back down. When you're out of the crowd, put RF gain back to full. The rest of how far a CB hears is explained in CB radio range.

A father and teenage daughter laughing beside a pickup in a driveway on a fall afternoon, the daughter giving a thumbs up
Set the knobs with the engine running; squelch adjusted in a silent garage will be wrong on the road.

ANL, NB and noise you can't knob away

Cobra's advice is to leave ANL on in "almost all vehicles" and use the noise blanker only when needed, since NB lowers sensitivity a little. NB works best on regular, repeating pops such as ignition noise. If you still hear a whine that rises with engine speed, that's alternator noise coming in on the power wiring, and no front-panel switch removes it. Fixes are in the wiring: power leads run toward the battery, a solid ground, and the coax routed away from inverters and light-bar wiring. One forum poster with a Cobra 29 traced his "squelch problem" to an inverter; turning it off cleared the noise.

Mic gain and modulation

Cobra says to run Dynamike fully up and back it off only if a power mic causes squealing or distortion. Turning it up won't make a stock radio illegal: for AM, the rules require modulation of 85 to 100 percent and a built-in limiter on any CB over 2.5 watts that keeps it from passing 100 (95.975). What more mic gain does add is background noise, so in a loud cab, a noise-canceling mic helps more than another quarter turn. Our CB microphone guide covers power mics like the Cobra HG M75 and when they help.

The same controls under different names

FunctionCobraUnidenPresident (Randy III)
Mic gainDynamikeMic gain (PC68LTXFM)Check manual
Receive fine-tuneDelta Tune; Voicelock on SSBClarifier on SSB modelsCheck manual
Noise filtersANL, NB, SoundTrackerANL, NB, Hi-CutANL, NB, Hi-Cut, NRC
SWRSWR CAL knob and S/RF-SWR-CAL switch (29 LTD Classic)Integrated SWR (Bearcat 980, PC68LTXFM)Not listed
Quick channelsCH9/19 switchInstant channel 9Check manual

Cobra names from its support articles and the Cobra 29 LTD Classic listing; Uniden from the PRO520XL, Bearcat 980 and PC68LTXFM listings; President from the Randy III listing. The Uniden "clarifier" name is general SSB usage; check your manual for the label.

Not every radio has every control. The compact PRO520XL, for example, lists RF gain, squelch, an ANL switch and a PA switch, but no mic gain or SWR meter. Our guide to the best CB radios lists which radios have what.

Switches that cause "my radio is broken" calls

  • CH9/19 switch left on. The radio stays on 9 or 19 and the channel knob does nothing. Cobra says to keep it in NORMAL. Channel 9 is reserved for emergencies and traveler assistance by rule (95.931); the full list is on our chart of CB channels.
  • PA/CB switch on PA. Your voice goes to the PA speaker, not over the air. The PA jack is also not the external speaker jack. If you want louder receive audio, see our CB external speaker guide.
  • Meter switch left in CAL or SWR after a check.
  • USB or LSB selected on an SSB radio when everyone around you is on AM.

"Calibrating" a CB: what you may and may not turn

Search "how to calibrate a CB" and you'll find guides to opening the case and turning the modulation or power trimmers. That's not an owner adjustment. Part 95 says internal adjustments and repairs "must be performed by or under the supervision of an individual who is qualified to maintain and repair transmitters" (95.319(b)), and modifying a CB for more modulation or power voids its certification and makes it illegal to operate (95.337). The legal limits stay 4 watts on AM or FM and 12 watts peak on SSB (95.967).

The calibration that belongs to you is the SWR CAL knob, which sets the meter before a reading. More range comes from the antenna, not the inside of the radio.

Fix-it table

SymptomLikely causeTry
Hear nothing on 19 on a busy roadSquelch too high, or RF gain downSquelch down to hiss, back up just past it; RF gain full
Red SWR or ANT light when you key upMistuned antenna, bad mount ground or damaged coaxCheck SWR on 1 and 40; inspect the mount and coax
Whine that rises with engine RPMAlternator noise on the power leadsRe-run power toward the battery; check ground; filter
Popping like a ticking clockIgnition noiseNB on
Voices sound like Donald DuckSSB station heard on AM, or off-tuneSwitch to the matching sideband; center delta tune or clarifier
People say you're quietMic gain down, or SWR highMic gain up; re-check SWR
People say you squeal or distortPower mic plus full mic gainTurn mic gain down
Channel knob does nothingCH9/19 switch engagedSet it to NORMAL

If the red light stays on after a good antenna check, stop transmitting and have the radio looked at. The rules require you to stop using a transmitter you know is malfunctioning, except for emergencies, until it's repaired (95.319).

Sources: Cobra support, "CB control settings" and "CB radio operation: front panel controls"; product listings on Amazon checked October 21, 2026; eCFR 47 CFR Part 95 (Title 47 up to date as of October 19, 2026): 95.319 · 95.337 · 95.931 · 95.967 · 95.975. Rules checked: October 21, 2026. How we research · Affiliate disclosure

Questions people ask

What should RF gain be set at on a CB?
All the way up for normal driving, which is Cobra's recommendation: RF gain sets receiver sensitivity, and full gain gives maximum range. Turn it down only when a nearby station is so strong it distorts, or when you want to hear just the close trucks on a crowded channel.
How do you set squelch on a CB radio?
Turn squelch fully down so you hear the hiss, then turn it up slowly just until the hiss stops. Stop there. Cobra warns that squelch set any higher than necessary reduces your receive range, because weak stations no longer open it.
What does delta tune do on a CB?
It fine-tunes the receiver slightly above or below the channel so a station that's a little off frequency sounds clear. Cobra says Delta Tune affects only received signals, not your transmission, and should normally sit at the 12 o'clock position.
Should ANL and NB be on?
In a vehicle, turn ANL on; Cobra says it will be necessary in almost all vehicles to cut engine noise. Use the noise blanker (NB) only when you need it, for repetitive popping like ignition noise, because Cobra notes it slightly lowers receiver sensitivity.
How do I tune my CB radio without an SWR meter?
If your radio has a built-in SWR function (the Cobra 29 LTD Classic and Uniden Bearcat 980 do), use it: set the switch to CAL, key the mic, set the needle to the mark, then switch to SWR and read. Radios without one need an external 27 MHz SWR meter placed between the radio and the coax.
Can I calibrate my CB radio to get more power?
No. Raising power or modulation is a prohibited modification under 47 CFR 95.337, and internal adjustments must be made by or under the supervision of a qualified person (95.319(b)). The owner-side 'calibration' is the SWR CAL knob, which only sets the meter.